Netscaler Gateway Plug In 2.1.4 For Mac
Hey guys thanks for your replies, fastethernet 0/0 is not getting an address, here is the information. One more thing, I have it connected to rogers, and I think that their cable modem is registered to work with one MAC address, because on my old linksys router I had to do a mac address clone of my machine, is there something like that on the cisco router? If you install a fresh copy of Mac OS High Sierra on a new machine (not upgrade) and try to install NetScaler Gateway plugin for Mac, then you will see a popup indicating that the system extensions signed by 'Citrix Systems Inc.” were blocked.
Hi there,I have a Cisco WLC 2100 that i have configured to have 2 networks on 2 different VLANS, they are setup on the config as ssid 'guest' and 'staff' I have setup on my ciscos dhcp scopes to serve these seperate vlans.eg this is the config on the core switch for the guest VLANip dhcp pool vlan8network 10.3.1.0 255.255.255.0domain name mydomain.comdns server 10.2.1.4default router 10.3.1.1lease 3then on the WLAN controller i have the 5th interface plugged in to a cisco switch and the port is set to this vlan. Then on the wlc i have an interface setup for the 5th port given it the ip address of 10.3.1.5 and the primary dhcp server is set to that of our core switch. But DHCP does not come through via the wireless. I have plugged a pc direclty in to the port on the switch and it get's an address from the switch.I have also gone in to the wlans and clicked on the profile name and edited the DHCP server override and inserted the core switch ip in there. But still no luck.any ideas please?
Hi there yes i plugged the pc in to each on the ports on the switch and got an DHCP address that was on each vlan eg port 20 was on vlan 13 and i got a.13 address and port 21 was on vlan 14 and got a.14 address, these ports are then respectivly patched in to the WLC and routed to each WLAN via the controller. So each Vlan has its own port and link to the switch as i don't want the guest network on ours and to be on it's own vlan.For the ports on the actual switch they are plugged in tointerface GigabitEthernet0/20switchport mode accessspanning-tree portfast!interface GigabitEthernet0/21switchport mode accessspanning-tree portfast. WLC config is hereNetwork Information RF-Network Name.
Ilrfgrp Web Mode. Enable Secure Web Mode. Enable Secure Shell (ssh). Enable Telnet.
Enable Ethernet Multicast Mode. Disable Mode: Ucast Ethernet Broadcast. Disable User Idle Timeout.
300 seconds ARP Idle Timeout. 300 seconds ARP Unicast Mode. Disabled Cisco AP Default Master. Disable Mgmt Via Wireless Interface. Disable Mgmt Via Dynamic Interface.
Disable Bridge AP Zero Config. Enable Bridge Shared Secret. Youshouldsetme Allow Old Bridging Aps To Authenticate. Disable Over The Air Provisioning of AP's. Enable Mobile Peer to Peer Blocking.
Disable AP Fallback. Enable Web Auth Redirect Ports. 80 Fast SSID Change. Disabled 802.3 Bridging.
Hi,Apologies for not reading the entire thread but to get this working, ensure the following:1. Switchport connecting the WLC must be a trunk port allowing the relevant vlans i.e. Management vlan, vlan 8 and your staff vlan.2. On WLC, configure management + ap-manager IP Address, subnet, gateway to be consistent with your switching Management VLAN i.e. If management vlan is vlan 50 then tag these interfaces with vlan 50.
Iriver internet audio player ifp 300 drivers for mac. If Mgmt VLAN is untagged then leave this to be tagged as 0 not 1. 0 means untagged on the Cisco WLC. Note: mgmt + ap-manager have to be different ip address but in same subnet.3. On WLC, configure two dynamic interfaces: guest and staff4. On WLC, configure WLANs with appropriate settings matching with appropriate dynamic interface.Hope this helps.